This is an 8080 emulator running the 1978 Space Invaders game by Taito, written in Rust. space-invade.rs is my third emulator (the first one was Chip-8 and then an Apple ][ emulator, both written in Kotlin). I chose Rust for this project to experiment with a different design and see how far I could push the performance.

On Windows, you can just cargo run --release (make sure you have SDL2.dll in the current directory).

On macOS, you will need to install SDL2 first (brew install sdl2).

I haven't tested on Linux.

cargo test will run the cpudiag emulator test.

• Press C to insert a coin.
• Press 1 or 2 to select the number of players.
• Player 1: left and right arrows to move, space to shoot.
• Player 2: a and d to move, s to shoot.
• 'p' will pause the game, any key will resume.
• ESC to close the window.

The 8080 turned out to be quite an advanced processor and even though it came out before the 6502 (1974 and 1975 respectively), I grew to appreciate its rich set of instructions (the 6502 only has 56, the 8080 has over 200) and how elegantly you can write some algorithms.

The emulator in this project is close to complete, including:

• All the instructions
• Correct cycle count
• Implementation of binary coded decimal (DAA)
• Interruptions (EI and SI and some RST but not all since Space Invaders only uses a few)

The emulator also passes the cpudiag diagnostic application, which you can run with cargo test.

The arcade game had quite an interesting architecture, please see the resources section if you need in-depth details. In a nutshell:

• The resolution is 224x256 with one bit of depth, so just black and white. The arcade used tranparent green and red tapes on top of the screen to simulate additional colors, which this emulator does as well.
• The graphic memory starts at 0x2400 with each byte representing eight bits (note: the screen is flipped 90 degrees).
• The video generates two interrupts: one when the beam is halfway through the screen and one at the end of the screen (VBL). Each of these interrupts calls a RST which tells the CPU to jump at $08 and $10 respectively. These two addresses are in charge of updating the half of the screen that the beam just finished drawing (quite a clever hack). My emulator doesn't go to that level of details and simply refreshes the graphic during the VBL.
• While the 8080 knows how to shift bits, it only has instructions to shift by one bit, and these are pretty slow, which makes shifting variable numbers of bits costly. This is unfortunate since it's the only way that this hardware can animate its graphics, so the designers created a multiple bit shifter outside in the game hardware itself and hooked it up with its input and output instructions. Refer to the detailed architecture (or the code) to understand how this works, but I thought this was another very clever design around hardware limitations of the time.

The main logic is in the file sdl2.rs, which spawns the emulator in a separate thread. That thread updates the graphic memory which the SDL 2 main loop uses to draw the graphics on the main screen.

The emulator is calibrated to run at 2Mhz with the following logic, which you will find in the run_one_frame() function:

• Run as many cycles as necessary to reach the first half of the screen (about 16,500)
• Generate the first interrupt
• Run as many cycles as necessary to reach the end of the screen (33,000)
• Generate the second interrupt

This function is called for each frame but the caller will sleep if needed so that the next frame isn't drawn until 16ms have elapsed (60Hz). You can find this code in sdl2.rs. Without this delay, this is what the game at normal speed will look like, running at about 70Mhz instead of 2Mhz:

Note that letting the game run like this for a little while is a good way to test that your code doesn't have any bugs that only show up on the long run...

Despite this, I can't shake the feeling that my Space Invaders is running a bit faster than the original, based on watching some footage of the actual arcade game, but I'm not 100% sure. Feel free to let me know if you find a bug in my timing routine that might explain my impression.

When I wrote my Apple ][ emulator, I first developed the 6502 emulator with a diagnostic file that was extremely thorough, and which gave me a pretty much 100% guarantee that once all these tests pass, my 6502 is flawless and I can now focus on the Apple ][ part without worrying about CPU bugs. I started this project with the same assumption and it was a mistake. Deep into the development, I was displaying graphics that made no sense and after hours of disassembling and understanding what the 8080 code actually does, I ended up finding two CPU bugs which cpudiag had not found.

And one of them was really trivial: I hadn't implemented the MOV E,A instruction correctly. This is a very simple instruction which moves the content of A into E, but I made a typo in my code and moved it into D instead... The other bug was in my implementation of DAD.

Moral of the story: you might have to add tests of your own, and at any rate, you cannot embark on such a project without developing a fluent ability to understand the assembly you are emulating.

It's becoming a meme now that Rust is struggling in the graphics library department (exhibit A) and in the game department (exhibit B). Finding a library that would make it easy for me to implement this project with very simple requirements (basically just need a frame buffer, possibly some simple GUI widgets) took me way too long. I ended up settling on SDL 2, but the bottom line is that developing GUI's and graphics in Rust on Windows is not exactly a walk in the park.

I'm probably done with this project but if I were to come back to it to improve it, I would probably:

• Make it run in the browser with WASM
• Sound
• The graphics still seem a bit janky to me, I'm probably doing something wrong in the SDL 2 event handling
• Make it do less busy waiting
• Show the controls so the user doesn't have to guess
• Add a debugger, breakpoints, etc...

The following documentation was invaluable to pull off this fun project:

• 8080 Reference Manual
• Emulator 101 (note: not https)
• Space Invaders assembly listing
• cpudiag assembly listing